Microtronik Autohex II BMW Full Package

Original Microtronik Autohex II HW4 BMW Full Package

Autohex II for BMW is full of advanced functions that will help you to solve problems you thought they are out of your hands.
Autohex II HW4 and full functions available in BMW from ISN read write to key programming and BMW ECU Programming and coding (HexTag is included).

Using Microtronik Autohex II BMW Full Package you can do as following:

• Read old ISN in BMW E series for following Ecus: D62M57A0, D62M57B0, D60PSA0, D50M57A0, D50M57E1, D60M47A0, D60M57A0, MEV9N46L, ME9N45, ME9N62, ME9E65_6, N73_L0, N73_R0, ME9N62_2, MSV70, MS450DS0, N62_TUE, N62_TUE2.
• Read Long ISN (SK) in BMW E series from following Ecus: MSV80, MSD80, MSD81, MSD85, MSD85Y, MSS60, MEVD176K, ME17N45, MED17_2, MED17_2N, MEV17_2, MEV17N46, MEVD174K, MEVD174KW, MV1722, MVD1722, MEVD172, MEVD1724, MEVD1725, MEVD172Y, MEVD17KW, D70N47A0, D70N47B0, D71N47A0, D71N47B0, D71N47C0, D71N47D0, D72N47A0, D72N47B0, D73N47A0, D73N57A0, D73N57B0, D73N57C0, D73N57D0
• Read Long ISN (SK) in BMW F series from following Ecus: MEVD172Y, MEVD172, MEVD1724, MEVD1725, N63TU_L0, N63TU_R0, S63TU_L0, S63TU_R0
• Read/Write long ISN (SK) in BMW E and F series on Bench using Factory Mode. No need to open the DME/DDE (Only Autohex II can do this function)
• ISN Reading from Tricore Ecus by boot mode.
• Indivedual Programming for any Ecu in BMW E and F series
• Ecu Swapping if hardware is matched.
• CAS1, CAS2, CAS3 and CAS3+ read and write ISN and SK
• Key Programming For E and F series (CAS1, CAS2, CAS3, CAS3+, CAS4 ,CAS4+, FEM, BDC)
• BMW E series EGS ISN matching with CAS
• BMW F series EGS 6HP and 8HP EWS Resetting
• BMW E Series, F Series and G Series coding for all Ecus (calculation of Ecucoding is calculated from FA)
• BMW advanced coding (manual coding)
• Vehicle order modification and backup and restore from LM,FRM,...ETC
• Do diagnose and service functions from Autohex II (Read and erase fault codes, data stream values, activations, reset adaptation,...)
• Use BMW ISTA-D on Autohex II WVCI (BMW ISTA-D Driver)
• Unlock secrity of BDC and FEM to able to: Change BDC and FEM VIN, Change BDC and FEM ISN, Mileage Reset for BDC and FEM, and making a key for BDC and FEM.
• Read and write ISN of MSD85, MSD87, MSV90 in F series.
• ECU Cloning/Tuning for a wide range of brands. This function is free for 90 days (Check Supported ECU List).
• Read and write CAS 1,2,3,4 EEPROM and FLASH 100% safely using HexTag tool.
• Read and write other modules from BMW,Mercedes, Audi, and others BDM protocol by HexTag tool
• Modify KOMBI Mileage by HexTag tool
• Renew all BMW keys, and many other brands by HexTag tool.

Notice:
1. HexTag ECU Cloning Function is free for 90 days only.
After 90 Days, ECU Cloning License will cost $1000, and $350 for annual update fee.
2. We offer one year warranty, while return for refund is not acceptable.

Autohex II BMW Full Functions:

Programming BMW ECU Individually
BMW ECU Programming is an easy to use with Autohex II, it performs Flashing the Ecu with latest version,code it,Change VIN, and other functions in one step

BMW ISN Reader & Writer Software
BMW ISN Editor Software in Autohex II lets you read ISN from DME, match it with CAS. This is essential for DME or CAS replacement, Autohex reads ISN from wide range of DME/DDE

Coding BMW ECU Individually
Autohex II Ecu coding for BMW is a straight forward function, you can choose between Auto and Manual coding to encode the Ecu you wish

BMW ECU Manual Coding
Autohex II BMW Software can do two methods of Ecu coding, auto coding which will be calculated from FA, and a manual coding for Ecu modification

BMW Vehicle Order Editor
Autohex II BMW Software can write FA into CAS from other ECU,backup FA in other Ecus, also you can modify the vehicle order safely

BMW EGS ISN Synchronization
Autohex II supports EGS EWS Reset for 6HP in E series and EGS EWS Reset for 8HP in F and G series, only few steps are required

CAS Firmware
For making keys, reading ISN and changing VIN for CAS which comes with specified part numbers, will not work just through direct reading, CAS Firmware function should be done to make it work

BMW Key Programming E Series And Mini
BMW Key programming by Autohex II is done by OBD, No dump is required. including CAS with latest update and all keys lost. it supports all BMW Models as well Mini cooper.

FEM & BDC Unlocking
Autohex II is the only tool that can unlock FEM/BDC without soldering, and it is the only tool that regenerates a secret file, and the only tool that can restore FEM back

AutoHex II BMW Latest Update Information:

AutoHex II BMW Diagnostic Software Version 1.0.56
ISN Factory mode for MEV1723 DME (MINI and F series) has been added in this version.
EGS EWS Reset function is able to support more versions of EGS in F and G series.
USB Driver has been upgraded to support latest versions of Windows 10.
Power supply monitor in Autohex II HW4 has been improved to allow poor power supply
to be able to work with AutoHex.

AutoHex II BMW Diagnostic Software Version 1.0.55
ISN Factory mode is available in this version. With this function you can read/write
ISN in DME and DDE besides to modify the working hours without opening the DME/DDE.
We are happy to announce that Autohex II is the only tool that supports this feature.
Flash data updated for BMW F and G series as well as MINI and Rolls Royce.
Ecus calculations from BMW vehicle order has been enhanced to support latest models in F and G series.
ISN by OBD II for F series has been enhanced to support more Ecus versions.
ISN Boot mode has one more DDE to support.

AutoHex II BMW Diagnostic Software Version 1.0.54
A new function for replacing FEM/BDC (including key transferring from original to donor) is available in this version, users can use this function from CAS replacement.
Deleting keys from CAS4,CAS4+ FEM and BDC is available in this version, users can use this function from key programming.
Fixed the FA parsing for new models (2018-2019) in F and G series.
Turkish language is supported starting from this version.
Other languages is updated in this version.

AutoHex II BMW Diagnostic Software Version 1.0.48
Added following models for coding and programming: F23, F88, F90, F97, F98, G01, G02, G08, G11, G12, G13, G30, G31, G32, G38.
Mileage reset for FEM and BDC is available from Unlocking Function (see picture).
ISN can be written in FEM and BDC (from ISN manager)
Added new diagrams in ISN boot mode to help HW4 users in making the connections.

AUTOHEX BMW Version 1.0.47
A new enhanced software version is available for all BMW Autohex users which rectified all issues regarding FEM/BDC unlock and more stabilized for programming ECU using E-net. Unlike the old versions getting secret file from FEM/BDC can be done all on bench.
No need to go for advanced option for unlocking.
Software has become 100% safer and stable for programming FEM - GW and FEM - BODY on bench without any working key.
Also Ethernet allows users to flash units like HU-H,KOMBI..etc in F series in reduced time period without any error.

Autohex II BMW Technical Parameters:

• Processor ARM Cortex M3
• Power Supply 8-18V
• Power consumption 2.5 -3.5W
• Max Working Temperature 50 ℃
• Diagnostic socket EOBD II16 Pins
• Host Interface Full Speed 12MBPS USB 2.0
• Wireless Connection Wi-Fi 802.11 b/g/n
• Operating system Win7, Win8 and Win10

Autohex II BMW Full Package List:

• Autohex II Hardware WVCI HW 4
• The Powerful HexTag BDM and Key programmer
• BMW Software Standard License
• ISN Boot Mode License
• BMW ECU Programming License
• BMW Key Programming License
• BMW ISTA/D driver to run dealer software
• 1 Year Technical Support
• 1 Year Hardware Warranty
• 1 Year Online Access for Online Programming