XPROG-M V5.84 ECU Programmer: Latest Version with USB Dongle

The XPROG-M V5.84 is the latest version of the X-PROG Box ECU Programmer, featuring:

XPROG-M V5.84 Highlights

• Latest software version: V5.84, Firmware: V4.4
• No need for a USB Dongle or activation.
• New authorizations added: AUTH-0028-1 Renesas V850 Authorized and AUTH-0028-2 Renesas SuperH Authorized (effective since 2017/10/9).
• Available in English.

XPROG-M V5.84 Using Tips

• This dongle is not compatible with older versions of Xprog; the software must be updated to V5.84 first.
• Close all antivirus software to prevent the X-prog software from being killed.
• Disconnect the internet to avoid hardware damage.
• Uninstall any previous version of Xprog-M or Xprog Box before installing the new V5.84 software; otherwise, the hardware may be damaged and lose its warranty.
• Avoid online updates as they can damage the hardware.

XPROG-M V5.84 Authorizations

• AUTH-0001: Motorola HC05 family authorization (read/write EEPROM).
• AUTH-0002: Motorola HC08 family authorization (read/write EEPROM).
• AUTH-0003: Motorola HC11 family authorization (read/write EEPROM).
• AUTH-0004: Motorola HC12, 9S12 family authorization (read/write EEPROM and flash memory).
• AUTH-0005: Texas Instruments TMS370/TMS374 family authorization (read/write EEPROM).
• AUTH-0006: Motorola HC05Bxx and HC05Xxx family bypass security authorization (read/write secured EEPROM and flash memory).
• AUTH-0007: ST M35080 authorization. Read/Write/Erase device to delivery state.
• AUTH-0008: BMW EWS3 authorization.
• AUTH-0009: ATMEGA family authorization (read/write EEPROM and flash memory).
• AUTH-0010: MB ZGS001 authorization.
• AUTH-0011: Motorola HC11EA9/E9 bypass security authorization (read/write secured EEPROM and RAM memory).
• AUTH-0012: National CR16 authorization (read/write EEPROM memory).
• AUTH-0014: ST7, ST10 family authorization (read/write internal flash).
• AUTH-0015: MPC5xx authorization.
• AUTH-0018: Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (read/write secured EEPROM and flash memory).
• AUTH-0020: ARM (Micronas, ...) Family authorization.
• AUTH-0021: ARM (Micronas, ...) Family bypass security authorization.
• AUTH-0023-1: MAC7xxx
• AUTH-0023-2: XC23xx
• AUTH-0024-1: MC9S12Cxx
• AUTH-0024-2: MC9S12XE
• AUTH-0024-3: 9S12XE SECURITY
• AUTH-0024-4: MC9S12HA/HY/P
• AUTH-0025-1: MPC/SPC5xxx Authorized (effective since 2016/3/13)
• AUTH-0027-1: HC(S)908 update Authorized (effective since 2016/3/13)
• AUTH-0027-2: HC(S)908 sercurity Authorized (effective since 2016/3/13)
• AUTH-0028-1: Renesas V850 Authorized (effective since 2017/10/9)
• AUTH-0028-2: Renesas SuperH Authorized (effective since 2017/10/9)

XPROG-M V5.84 Adapters

• ADP-0001: TMS370 PLCC28 programming adapter.
• ADP-0002: TMS370 PLCC44 programming adapter.
• ADP-0003: TMS370 PLCC68 programming adapter.
• ADP-0004: Motorola HC05B/X PLCC52 programming adapter.
• ADP-0005: Motorola HC05B/X QFP64 programming adapter.
• ADP-0006: ST M35080 in-circuit programming adapter.
• ADP-0008: TMS374 family in-circuit programming adapter.
• ADP-0009: MC68HC05V12 programming adapter.
• ADP-0010: TMS374 on-board programming adapter.
• ADP-0011: HC11EA9/E9 programming adapter.
• ADP-0017: HC(S)12 BDM / ARM Micronas in-circuit programming/bypass security adapter.
• Additional adaptors for 5M48H P-Flash (ADP-0019 Rev.A).
• EWS3 adaptor, EEPROM adaptor, QFP28 adaptor, QFP64 adaptor, QFP80 adaptor, QFP112 adaptor, QFP144 adaptor.

Windows System Requirements for XPROG-M V5.84

• The system should be Windows XP (32-bit) or Windows 7 (64-bit), with all necessary patches installed and the system functioning properly.
• The system must have at least two partitions, excluding the CD ROM partition.
• Virtual hard disks are not supported.

XPROG-M V5.84 Installation Instructions

1. Click "installation.reg" and import it into regedit.
2. Install "AdbeRdr11000_zh_CN.exe"; this is essential for the Xprog software to start.
3. Connect the Xprog main interface to your computer and install the USB driver.
4. Copy the folder "XPROG-BOX5.84" to the desktop, open it, and run "xprogdesktop.exe".

XPROG-M V5.84 Software Display

List of Supported Chips:

Package Includes

• 1 PC XPROG-Box Hardware (Aluminum Enclosure)
• 20 PC Adapters Set
• 1 PC USB Cable
• 1 PC USB Dongle
• 1 PC CD with XPROG-Box Software (V5.84)