New 6" LED OBD-II HUD Head Up Display Over Speeding Warning/Speed /Km rpm /Shift/ light /Temperature

New 6" LED OBD-II HUD Head Up Display Over Speeding Warning/Speed /Km rpm /Shift/ light /Temperature

1. Overview

Thank you for purchasing HUD. HUD is researched and developed for driving safety. Whether driving during the day, or driving at night and whether driving at high-speed,or driving at low speed, you do not have to look down at the instrument panel. HUD project the important car information (such as car speed, engine speed, water temperature, fuel consumption, etc.) onto the windshield. So when you are driving, you can easily control the car's vital information to reduce or avoid accidents or traffic accidents. At the same time, HUD can reduce your eye fatigue effectively so that you achieve the driving pleasure and driving safety perfect unity.
HUD is designed by very powerful and stable integrated circuits and meet the relevant standards. and add a beauty for your car by unique shape and elegant, flowing lines, natural beautiful body.

2. HUD structure

2.1 HUD structure

1. 【MPH】─Mile / hour
2. 【KM/H】─Kilometer/hour
3. 【RPM】─R /M, an engine speed
4. 【Parameter】─Including KM/H,RPM,MPH
5. 【Shifting reminding】─This Icon lights means you need to shift
6. 【Engine faulty】─This icon is on means the engine is faulty and needs to be immediately removed
7. 【USB interface】─OBDII cable connects to USB
8. 【Engine Speed】─This icon display engine speed，unit：*1000
9. 【Dial Switch】─Can be up, down, straight press
10. 【Photosensitive Icon】─It’s used to adjust the display brightness of HUD automatically
11. 【Speed Alarm】─When the car exceeds the speed limit, the icon flashes
12. 【Sound Icon】─This icon is lit, the sound switch is on
13. 【Parameter】─To display L / 100KM, L / H, the value of L
14. 【Parameter】─To display the value of V, S, ℃, ℉, KM
15. 【L 】─L shows the remaining oil, lights means you need to refueling the car
16. 【L/H】─Indicates fuel consumption per hour
17. 【L/100KM】─instantaneous fuel consumption per one hundred kilometers
18. 【KM】─This icon is on, you can know the car mileage
19. 【°C °F】─show the water temperature of the car or Fahrenheit respectively
20. 【V S】─represents the voltage (V), the acceleration time of car from the start to 100km/h respectively (the function is optional, and only for compass)
21. 【】─These icons show the current display content of voltage, throttle, water
temperature, ignition timing, one hundred kilometers acceleration respectively
22. 【E、S、W、N、NE、NW、SE、SW】─These icons show the directions of east, south, west,
north, northeast, northwest, southeast, southwest Respectively (this function is optional, and only for compass)

3. Main Features

1） Detecting car’s OBDII interface automatically and all car with OBD II or EUOBD are OK,
plug and play;
2） Car speed, engine speed, water temperature, voltage / throttle position / Ignition angle /
one-hundred-kilometer acceleration time, instant fuel consumption, average fuel consumption,
mileage, fuel shortage reminding, engine faulty, shift reminding, etc. are displayed.
3） Normal display mode, high-speed display mode and automatic display mode are set by
yourself;
4） Kilometers and miles are free to switch, which greatly facilitates the dashboard of British
Standard;
5） 6 inches display area, easy to read
6） Switch on and off automatically, HUD start when car starting , HUD shutdown when the
engine is turning off to protect the car battery effectively; at the same time, you can switch on and
off HUD by Manually Shutdown to protect the battery safety.
7） Single-stage and four-stage overspeed alarm for driving safely.
8） Engine speed alarming so that you can shift timely to save fuel, also has a special significance for the novice;
9） Automatic and manual brightness adjustment mode, no dazzling;
10） Compass (this function is optional), the precise position, car does not get lost; Accurately
determining the position and not get lost

4. Installation Instructions

4.1 Make sure if your car complies with OBD II (or EU OBD) interface standard;
4.2 Open up the engine hood and look for the OBDII sticker. If there is a sticker of “OBDII
CERTIFIED” (Figure 2), then you can use our HUD. You can also check if your car have a
diagnostic Interface(the vast majority of cars made in china after 2006 have the diagnostic
Interface).
4.3 If your car has a diagnostic Interface of 16PIN(Figure 3), then plug the OBDII cable with the
diagnostic Interface of 16PIN.

4.4 Put the non-slip mat on the relatively flat position of the car console. Then you put HUD on
the non-slip mat and adjust HUD.
4.5 Reflective film can be attached to the front windshield above HUD so that you can read the
parameters form the reflective film.
Remarks: tips of sticking the reflective film
A. Firstly spray some water on the position of sticking the reflective film;
B. Remove the protective layer of the film, then attach to the corresponding position;
C. Adjust the location, then use a small scraper or a smooth object to scrape the surface of the
film;
D. After a few minutes, the moisture will evaporate, then gently wipe off the water droplets and
dust.
4.6 Power-on test
You switch on HUD and HUD shows the current car voltage. Then HUD searches the car
computer system. If HUD displays data, such as car speed, engine speed etc, it indicates that the
product has been installed successfully.

5. HUD setting method

The value HUD displays is the value of car inside computer system. Since the value that the
car dashboard displays is a little bit different from the value of car inside computer system , so you
can enter the setup mode to fine-tune the display value of HUD to achieve exactly the same
values that the dashboard displays.

5.1 Specific setup
Firstly, you need to connect HUD to the car, then press the OK button for 3 seconds to enter
the setting mode. You can press the OK button once, the value of Menu 3 increases by 1. The
value of Menu 1 increases or decreases by 1 by dialing up or down the dial switch once, which
achieves the same values of HUD as the value the car dashboard displays（Dial switch partially
shown in Figure 4 and HUD setting interface shown in Figure 5）

1) Enter the setup interface, each parameter adjustment value show as follows Table 1:

Menu 3	parameter	Setting range	Specific description	The default value  (Menu 1)
0	Car speed	50-150	50%-150%	100
1	Engine speed	50-150	50%-150%	100
2	Fuel consumption	50-150	50%-150%	100
3	Engine speed alarm	10-75	1000RPM-7500 RPM	50
4	Single-stage / four-stage speed alarm	0-1	0: Manually set up the Single-stage speed alarm; 1: set up the Single-stage speed alarm(60Km/h,80Km/h,100Km/h,120Km/h)	1
5	Single-stage speed alarm value	30-250	30km/h-250km/h	100
6	Display Mode	0-2	0: Automatic display mode- When car speed is less than 80Km / h, HUD displays all parameters, and display car speed and fuel consumption at high-speed mode of over 80Km/h； 1: HUD displays all parameters； 2: high-speed mode- displaying car speed and fuel consumption	1
7	Brightness adjustment	0-7	0: Automatic brightness adjustment; 1 is the darkest, 7 is the brightest	0
8	Fuel tank capacity	0-150	0L-150L	50
9	Fuel switch	0-2	0: To manually input fuel， 1: car has fuel Level Sensor， 2: Turn off this function	2
10	Enter the value of oil	0-150	refueling 0 L-150 L	25
11	Discharge capacity setup	0-100	0: Cars with air flow meter； 1:Set up the reference fuel consumption （Referring to the Ministry announced fuel consumption value or manufacturer’s corresponding fuel consumption value）； setup value:1,2,3,4…,100 means the discharge capacity value of 0.1L， 0.2L,0.3L,0.4L…,10.0L respectively	0
12	Starting Voltage	110-150	11.0V-15.0V	110
13	Shift reminding switch	0-1	0:switch off the Shift reminding； 1: switch on the Shift reminding；	0
14	Fuel consumption display	0-1	0: switch off the Fuel consumption display； 1: switch on the Fuel consumption display；	1
15	Reference fuel consumption	10-500	10-500 indicates fuel consumption per 100km from1.0 to 50.0 respectively, the value of 10, 11, ..., 500 represents fuel consumption value of 1.0L/100KM,1.1L/100KM…,50.0L/100KM	80
16	Alarm sound	0-1	0:turn off the Alarm sound， 1: turn on the Alarm sound，	1
17	Temperature Unit	0-1	0:°C；1:°F	0
18	Compass switch (optional)	0-1	0:OFF，1:ON	1

Symptom	Possible Causes	Solutions
No car speed alarm	The setup alarm value of the car speed is too high, or car speed alarm switch is off	reset up the reasonable alarm value or turn on the alarm switch
No engine speed alarm	The setup alarm value of the engine speed is too high, or engine speed alarm switch is off	reset up the reasonable engine speed alarm value or turn on the alarm switch
No response after power on	HUD switch is off	Turn on HUD and check whether the plug is inserted firmly
no sound	Alarm sound is off	Turn on the alarm sound
Compass doesn’t show direction (optional function)	Compass switch is off	Turn on the compass switch
Inaccurate fuel consumption	Without air flow sensor	Set up the relevant parameter values
No display	Car does not comply with EU-OBD or OBDII standard	Consulting the automobile manufacturers if the car meets the OBDII standard
No Mileage	Not set up the amount of fuel and some parameters of fuel consumption is set improperly	Manually enter the amount of fuel and adjust the parameters Of fuel consumption properly
Only display car speed and fuel consumption	Car speed is more than 80KM/H	Car speed is more than 80KM/H

Package including:

• 1pc x Host machine of HUD
• 1pc x Reflecting film
• 1pc x OBD2 Connecting line
• 1pc x Instruction Manual
• 1pc x Non-slip mat

---